---
title: "Vignette Guide"
space: "Vignettes"
url: "https://factory.uga.edu/vignettes/cv/image-recognition/guide"
updated: "2026-11-19"
---

# Standard Manual for Object Detection Vignette 1

1. Introduction
2. Bill of Materials
3. Assembly Instructions
4. Troubleshooting
  1. Hardware
  2. Software

## Introduction

This document contains information regarding the GA-AIM vignette including the Bill of Materials, instructions for processing materials, instructions for assembly, and troubleshooting information. 

Refer to the “Bill of Materials” section of this document to confirm your inventory of the materials required for the construction of the vignette. 

Refer to the “Processing Materials” section of this document for instructions to process materials from the Bill of Materials correctly. 

Refer to the “Assembly Instructions” section of this document for written instructions regarding the assembly of the vignette 

Refer to the “Troubleshooting” section of this document for instructions regarding the fixing of problems you may have. 

## Bill of Materials

ZIMA Board 

McMaster Materials 

- 2 Acrylic Sheet: 24” x 24” x ¼"
- 2 Acrylic Sheet: 12” x 36” x ¼" 
- 4 Acrylic Sheet: 24” x 48” x ¼” 
- 2 Wood Shelf: 12” x 72” 
- 4 T-Slotted Framing (Wheel)
  - Stem Mount Caster for 1.5” High Single Rail, 200 lb. Capacity
- 1 Phenolic Workbench Top 
- 1 Pair Steel Drawer Slides 
- 36 Black Corner Brackets 
- 1-½" Long for 1-½” High Rail T-Slotted Framing 
- 2 T-Slotted Framing (Outside Corner End Bracket) 
  - For 1-½" High Rail
- 2 T-Slotted Framing (3-Way Outside Corner End Bracket) 
  - For 1-½" High Rail
- 1 T-Slotted Framing: Double Extrusion/Double Six Slot Rail, 4 Ft  
  Black, 3” High x 1-½" Wide, Hollow 
- 5 T-Slotted Framing: Single Extrusion/Single Four Slot Rail, 10 Ft  
  Black, 1.5” High x 1.5” Wide, Hollow 
- 1 T-Slotted Framing: Single Extrusion/Single Four Slot Rail, 4 Ft  
  Black, 1.5” High x 1.5” Wide, Hollow

Surge Protector Block 

USB LED Light 

USED Extension 

Power Reels 

40” TV 

TV Mount 

Wireless Keyboard and Mouse 

Drawer Handle (3d printed) 

## Processing Materials

Cut two 66.5” Single Extrusions (SE) out of 2 separate 10’ SE 

From one leftover 4’5.5” SE (53.5” SE)  

```
Cut out one 21” SE, & one 29.5” SE 

    Repeat on other leftover 53.5” SE 

        3.5” leftover 
```

From three different 10’ SE, cut three 33” SE’s out on each one. 

```
Three 21” SE leftover 
```

From 4’ DE, cut two 21” DE’s out.  

```
6” leftover 
```

 From both 12” x 72” wood shelves 

```
Cut out one 32-1/8” x 12” piece, and one 19-7/8” 12”  piece. (Should have 2 of each) 
```

From one 24” x 48” acrylic sheet, cut out a 21 ¾” x 33” sheet. 

From another 24” by 48” acrylic sheet, cut out a 20 3/8” x 31 3/8” sheet. 

From another 24” by 48” acrylic sheet, cut out a 32 &amp; ¾" x 12” sheet. 

Tap one side of two 21-inch single extrusions (SE) with m8 x 1.25  

Tap the top side of two 29.5-inch SE’s with m8 x 1.25 and the bottom sides with 3/8-169C2B 

Tap both sides of two 33-inch SE’s with m8 x 1.25 

Tap the top side of two 66.5-inch SE’s with m8 x 1.25 and the bottom side with 3/8-169C2B 

Center the extension cord on the center shelf piece, place the place holders on the extension cord, and use them to mark the shelf piece. 

```
Drill through the marked locations and screw the place holders onto the extension cord and shelf piece using nuts and bolts (file the holes as necessary to screw the parts together) 
```

## Assembly

General Assembly:  
Sort and count all available pieces  

Guarantee all L Brackets have their tops lined up with the given measurements unless otherwise stated 

Side View Assembly:

Separate the smallest part of the drawer slide from the slide.  

On the 21” Double Extrusion 

Slide 5 3d printed inserts into the side of the 21” DE. 

The inserts should be slid into the part of the DE that you will face inwards on the vignette. 

The Inserts should in the top slot on the side of the DE  

Line the bigger parts of the drawer slide up with the 21” DE 

The Flat side of the drawer slide should be touching the DE 

The Front of the drawer slide (where the smaller part goes in an out) should be lined up with what will be the side of the DE that faces the front of the vignette 

Mark the Extrusion 5 times using the holes on the biggest part of the slide. Center the inserts with the marks made 

Realign the slide and pre-drill through the holes into the inserts. 

Screw into the holes to attach the slide to the DE. 

Begin with a side of the 66.5" SE to make the Vignette side 

Screw in L Bracket 5 inches from bottom of extrusion 

Slide in additional T nut above 5 inches 

Screw in L Bracket 29.5 inches from bottom of extrusion 

Attach 21" double extrusion to L Bracket 5 inches from bottom. 

Slide 2 T nuts in top side of 21” double 

29.5-inch single extrusion  

Screw in L Bracket 5 inches from bottom 

Attach to 21-inch double extrusion with 66.5 single” 

Attach L Brackets where 66.5” single and 21 double meets, and where 29.5” single and 21” double meets 

Attach L Brackets so that top faces downward (touching with the top of 21” DE” 

Repeat all steps to make a second side. 

Insert 21.5”x 22” side panel in spaces between 66.5” single &amp; 29.5” single 

Loosen and adjust L Brackets that are in the way as needed, then readjust to original position. 

Lay both assembled side parts flat and face both parts in opposite directions 

Following steps apply to both assembled side parts 

Attach 21” SE to L Bracket on 66.5” SE at 29.5 inches  

Attach 2 L Brackets at each end, outward facing 

Attach 2-way corner bracket atop 66.5” in a way that would be facing inward and screw in to connected parts 

Attach 3-way corner bracket atop 29.5” in a way that would be facing inward and screw in to connected parts 

Screw in L Bracket 4 inches from bottom of 66.5” single 

Screw in L Bracket 18 inches from bottom of 66.5” single 

Screw in L Bracket 29.5 inches from bottom of 66.5” single 

Screw in L Bracket 46.5 inches from bottom of66.5” single 

Screw in L Bracket 52.5 inches from bottom of 66.5” single 

Screw in L Bracket in line with top of 66.5” single 

Screw in L Bracket 4 inches from bottom of 29.5” single 

Screw in L Bracket 18 inches from bottom of 29.5” single 

Front and Back View Assembly:

Choose one side part for the following 

Set aside tapped 33” singles 

Attach non-tapped 33” SE to following L Bracket heights on 66.5” SE: 

4 inches 

18 inches 

29.5 inches 

46.5 inches 

Slide 2 T nuts inside the front-facing side. 

52.5 inches 

Slide 2 T nuts inside the front-facing side. 

Attach 33” SE to following L Bracket heights on 29.5” SE 

4 inches 

18 inches 

Attach tapped 33” SE to: 

 3-way corner bracket on 29.5” SE 

2-way corner bracket on 66.5” SE 

On 66.5” SE, insert back panels in spaces between extrusions at: 

4 inches &amp; 18 inches 

On 29.5” SE, insert front panels in spaces between extrusions at 

18 inches and 29.5 inches 

Insert Wood Shelf between front and back sides at 18” mark 

Line up other side part and screw together all pieces 

Stand Frame upward 

Screw workbench top into L Brackets that are facing outward &amp; connected to 21” SE on side frames 

Screw wheels in to bottoms of all 29.5” and 66.5” SE’s 

Assemble TV mount, center T nuts with TV mount, and attach TV and TV mount. 

Drawer Assembly:	 

On the wood shelf pieces, 

One inch from the bottom, carve a ¼” thick, 1/8” deep slit from the left end to the right end.  

Insert the 31 &amp; 3/8” x 20 &amp; 3/8” acrylic sheet in the 32 &amp; 1/8” piece so that it is centered.  

Attach the remaining 32 &amp; 1/8” shelf piece and 19 &amp; 7/8” pieces to the corresponding sides of the acrylic sheet.  

The long side of the drawer should be facing up for the next step. 

Drill holes to screw into 

Drill 3 holes on each end to secure the touching wood shelf pieces. 

Holes should be centered with vertical standing wood shelf pieces. 

Add screws and repeat on the other side. 

Take 32 &amp; ¾" x 12” acrylic sheet and line it up with the front of the drawer so that the tops are flesh with each other, and so that the sides of the acrylic are even on both ends of the drawer. 

Place acrylic side of the drawer facing down. 

Drill holes to from inside the drawer into the acrylic 

Line drill bit up with the drawer and mark where the drill would be to drill halfway into the acrylic. 

Drill until the drill enters halfway through the acrylic sheet 

Separate the acrylic sheet and the drawer, and drill into existing holes on the acrylic sheet until the drill enters halfway through the sheet. 

Line up the same side of the drawer with the acrylic sheet. 

Add screws.  

The acrylic side should be facing down to make it easier to add screws. 

Flip the drawer to face upright. Center the drawer handle, and drill two holes into the handle and top of the drawer. 

Add screws.  

On one side of the drawer, take the smallest part of a steel drawer slide and line it up 1 inch from the bottom of the drawer.  

The flat side of the drawer slide should be touching the drawer, and the front ends of the drawer and the drawer slide should be facing the same way. 

Drill holes into the center of the 4th, 8th, 10th, and 12th outlined holes from the front of the steel drawer slide. 

Add screws. 

Slide on the outer part of the drawer slide. 

Flip over and repeat the same steps for the drawer slide on the other side of the drawer. 

## Troubleshooting

### Troubleshooting Guide for the Object Detection Vignette's Hardware

1. **Mobile Stand**:
  - If the mobile stand is unstable or wobbly, check if all the wheels are locked securely in place.
  - Ensure that the stand is positioned on a level surface to prevent any tilting or tipping.
2. **Electric Power Plug-ins**:
  - If there is no power, ensure that the power switch is turned on and that the power cable is securely plugged into a functioning power outlet.
  - Check for any visible damage to the power cable and replace it if necessary.
  - Test the power outlet with another device to ensure it is working properly.
3. **Fixed Camera**:
  - If the camera is not turning on, check if it is properly connected to the power source and if the power switch is on.
  - Ensure that the camera lens is not obstructed by any objects or debris.
  - Test the camera with another power source or cable to rule out any issues with the camera itself.
4. **Computer**:
  - If the computer is not powering on, check if it is securely connected to the power source and if the power button is functioning properly.
  - Verify that all cables connecting the computer to the monitor, keyboard, and mouse are plugged in securely.
  - If the computer displays error messages or is not functioning as expected, contact technical support for assistance.
5. **TV**:
  - If the TV screen is blank, ensure that it is powered on and that the correct input source is selected.
  - Check if the HDMI or other video cable connecting the computer to the TV is properly connected at both ends.
  - Test the TV with another device to confirm if the issue is with the TV or the computer.
6. **General Tips**:
  - Restart the hardware components to see if that resolves any issues.
  - Check for any loose connections or damaged cables and replace them if necessary.
  - If troubleshooting steps do not resolve the issue, consult the user manuals for each hardware component or contact technical support for further assistance.

### Troubleshooting Guide for the Vignette's Software

1. **Web App Not Accessible**:
  - Ensure that the computer running the Docker container is powered on and connected to the network.
  - Check if the Docker container is running by accessing the command line interface and running `docker ps`. If the container is not listed, restart it using `docker start [container_name]`.
  - If the web app is still inaccessible, try accessing it from a different device or browser to rule out any local issues.
2. **Real-Time Model Not Working**:
  - Verify that the fixed camera is connected to the computer and recognized by the Docker container.
  - Check if the necessary drivers for the camera are installed and up to date.
  - Ensure that the correct camera is selected in the web app's settings or configuration menu.
  - If the real-time model continues to malfunction, restart the Docker container and try again.
3. **Image Capture Not Functioning**:
  - Confirm that the permissions for accessing the camera are granted within the web app.
  - Check if there is sufficient storage space available on the computer for saving captured images.
  - Restart the Docker container and try capturing images again.
4. **Training Data Sets Not Saving**:
  - Verify that the Docker container has write permissions to the directory where training data sets are stored.
  - Check if the disk space on the computer is not full, preventing the saving of training data sets.
  - Restart the Docker container and try saving the training data sets again.
5. **Training Process Not Completing**:
  - Ensure that the Docker container has sufficient resources allocated for running the training process, including CPU, memory, and GPU if applicable.
  - Check if there are any errors or warnings displayed in the web app's training log or console.
  - Restart the Docker container and try running the training process again.
6. **General Tips**:
  - If the issues persist after restarting the Docker container, try restarting the computer running the container.
  - Contact technical support for further assistance if the troubleshooting steps do not resolve the issues.