---
title: "Operation Manual"
space: "Vignettes"
url: "https://factory.uga.edu/vignettes/additive-manufacturing/operation-manual"
updated: "2026-11-19"
---

# Operation Manual for Additive Manufacturing Vignette 1

1. Introduction
2. Operation
3. Maitenance
4. Bill of Materials
5. Processing Materials
6. Assembly Instructions
7. Troubleshooting

## Introduction

This document contains information regarding the GA-AIM vignette including the operation, maintenance, Bill of Materials, instructions for processing materials, instructions for assembly, and troubleshooting information. 

Refer to the “Operation” section of this document to read about proper operation of the Additive Manufacturing vignette. 

Refer to the “Maintenance” section of this document to learn about best practices to properly maintain the vignette and included equipment. 

Refer to the “Bill of Materials” section of this document to confirm your inventory of the materials required for the construction of the vignette. 

Refer to the “Processing Materials” section of this document for instructions to process materials from the Bill of Materials correctly. 

Refer to the “Assembly Instructions” section of this document for written instructions regarding the assembly of the vignette 

Refer to the “Troubleshooting” section of this document for instructions regarding the fixing of problems you may have. 

## Operation

Operation of the Additive Manufacturing Vignette is as simple as plugging it in and waiting for everything to turn on and then starting a print. 

### Turning on the Vignette

To turn on the vignette, plug in the power plug in the rear into a standard wall plug. If more length is needed, pull on the cord to extend the length. The cord length will lock in place whenever a clicking noise is heard and will retract when silent. The system should only take 30 seconds or less to fully boot up. If the system was shut down properly, the screen should automatically pull up the printer dashboard shown below.

![](/files/DefaultDashboard.webp)

If instead of the screen above, there is a screen saying "Unable to Connect", try refreshing the page using the F5 key on the keyboard. If the screen starts with any page other than the dashboard above or the unable to connect screen, press ALT + F4 to close out of that tab and that should bring you to the correct screen. If anything on the dashboard such as the live camera feed or sensor data is not functioning properly, first try to press F5 on the keyboard, and if that does not work then shut down the vignette and restart. MAKE SURE TO SHUT DOWN THE VIGNETTE ACCORDING TO THE INSTRUCTIONS TO ENSURE PROPER FUNCTION. If the vignette is not properly shut down for some reason, a proper shut down may be required to restore normal functionality.

### Shutting Down the Vignette

**THIS SHOULD BE DONE ANY TIME THE VIGNETTE IS DISCONNECTED FROM POWER**

Properly shutting down the vignette is as easy as pressing CTRL + ALT + DEL on the keyboard and then pressing "SHUT DOWN" with either the mouse or the touch screen. Wait until the screens fully shut off to unplug the vignette.

### Dashboard Tab

The printer dashboard is a fully funtional, custom-made dashboard that shows all necessary printer data. Below is a diagram labeling what each part of the dashboard does. There are both interactive and non-interactive elements to the dashboard. Interactive elements serve some kind of function when pressed, while non-interactive elements just show data and can be clicked to see historical data. Interactive elements will be signified with an asterisk \* 

![](/files/DefaultDashboardLabeled.webp)

1. \*Dashboard Tab Selector - Selects the printer dashboard tab (tab that is currently shown)
2. \*Use Cases Tab - Selects the Use Cases Tab which will be discussed in the next section
3. \*Print Speed - Selects print speed by clicking the button of the desired speed (Only Available while Printing)
4. \*Pause - Pauses the current print and turns into a resume button while print is paused (Only Available while Printing)
5. \*Cancel - Cancels the current print (Only Available while Printing)
6. Task - Displays the name of the current file being printed
7. Progress - Displays the progress of the current print
8. Layer - Displays the current layer of the print
9. Stage - Displays the current step of the printing process
10. HMS Notifications - Displays any error messages
11. Start Time - Displays current print's start time
12. End Time - Displays current print's estimated end time
13. Remaining Time - Displays the remaining time left in the current print
14. AMS Temperature - Displays the temperature inside the Automatic Material System (AMS)
15. Filament Color - Displays the color of each filament inside the AMS
16. Filament Type - Displays the type of filament inside each of the AMS slots
17. Status - Displays the current status of the printer
18. Chamber Temperature - Displays the temperature inside the chamber of the printer
19. \*Chamber Light - Toggles the Chamber Light inside the printer ON or OFF
20. AMS Humidity - Displays the color of each filament inside the AMS
21. Bed Temperature - Displays the temperature of the Print Bed
22. Nozzle Temperature - Displays the temperature of the Nozzle
23. Completion Percentage - Displays the progress of the print as a percentage
24. Live Camera - Displays a live view of the print from inside the printer

### Use Cases Tab

The purpose of the use cases tab is to provide actual examples of how additive manufacturing is used within manufacturing enterprises. Within the tab there are 4 main use cases, each with their own "LEARN MORE" buttons that when pressed will show a popup with more information. To exit out of the popup, press the X in the top left corner or tap outside the popup.

![](/files/USE_CASES.webp)

![](/files/POPUP.webp)

### Starting a Print

Before starting make sure that: 

- The build plate is completely clean from previous prints 
- There is enough filament for the print 
- Empty the waste chute bucket on the back of the printer

Starting a print involves the touchscreen that is on the printer itself. If the touchscreen is not on and the printer is on, touch the screen to wake. On the left-hand side of the screen, navigate to the middle button that looks like a file folder. The screen should pull up pictures of files that are available to print. Choose the desired print file for your demonstration and click on it. On this page, make sure the selections match the ones shown: 

If the above criteria are met, then you are okay to select "Print Now".

### Bambu Studio

Bambu Studio is the slicer that the BambuLabs X1C uses. **DO NOT TRY TO CHANGE ANY WIFI OR NETWORKING SETTINGS ON THE BAMBULABS X1C. CHANGING THESE SETTINGS WILL BREAK THE VIGNETTE!!** Below are links to the Installation and Operation Instructions that give the basic instructions on how to install and use the slicer to slice a 3D model. Due to the way that the vignette is set up, wireless access to the printers is not available so print files must be manually uploaded to the printer using the Micro SD. Below is a video that gives simple instructions on how to use the SD Card to upload files to the printer to be printed. Lastly there is an article on how to use the AMS to create multi-color prints.

- [Installation &amp; Operation Instructions](https://wiki.bambulab.com/en/x1/manual/introduction-to-bambu-studio)
- [Print from Micro SD Card](https://wiki.bambulab.com/en/x1/manual/print-from-sd-card)
- [Use AMS on Bambu Studio](https://wiki.bambulab.com/en/software/bambu-studio/use-ams-on-bambu-studio)
- [General Bambu Studio Quick Start](https://wiki.bambulab.com/en/bambu-studio/quick-start)

## Maitenance

### Daily Maitenance

1. Visual Inspection: Check for any apparent damage or loose parts.
2. Bed Cleaning: Make sure bed is clean before printing. If there are bed adhesion issues, clean the bed using soap and water or with isopropyl alcohol.
3. Nozzle Cleaning: Be sure to verify that there is not plastic build-up on the nozzle, and clean it off if there is

### Weekly Maitenance

### Monthly Maitenance

1. Check for Wear and Tear: Inspect all moving parts for wear. Replace parts like the nozzle, PTFE tube, or any other components showing signs of wear.
2. Lubrication: Apply a high-quality PTFE lubricant to the smooth rods and lead screws. Do not over-lubricate; a small amount is sufficient.

### Bi-annual Maitenance

1. Hotend Maintenance: Disassemble, clean, and reassemble the hotend to ensure it's free of clogs and debris. Replace any worn-out parts.
2. Firmware Update: Check for the latest firmware updates from BambuLabs and update your printer to ensure it benefits from the latest improvements and bug fixes.
3. Electronics Check: Visually inspect all electronic connections for signs of wear or corrosion. Re-seat any connectors that seem loose.

### Annual Maitenance

1. Deep Clean: Conduct a thorough cleaning of the entire machine, paying special attention to hard-to-reach places where dust and filament debris may have accumulated over time.
2. Review and Replace: Evaluate all Replaceable parts and replace as necessary based on wear. This includes parts such as bearings, belts, and any other components that show signs of deterioration.

### Additional Considerations

- Always follow safety guidelines when performing maintenance, especially when dealing with the printer's hotend or electrical components. 
- If you experience printing issues, consult the troubleshooting section of your BambuLabs X1 Carbon manual. 
- Keep your BambuLabs X1 Carbon on a stable and level surface to prevent any misalignment issues. 
- Use only recommended filament types and brands to avoid clogging and ensure the best print quality.

## Bill of Materials

- ZIMA Board 
- Bambu Labs X1C w/ AMS 
- Mini DisplayPort to Dual HDMI Splitter 
- Monitor Mount 
- Touchscreen 
- USB C 180 Adapter 
- HDMI 180 Adapter 
- Cable Sleeve 
- 8' HDMI Cable 3 Pack 
- 10' USB C Cable 2 Pack 
- Ubiquiti Router 
- POE Adapter 
- Textured Build Plate 
- Black PLA Filament (3) 
- White PLA Filament (3) 
- Red PLA Filament (3) 
- *McMaster Materials* 
  - 2 Acrylic Sheet: 24” x 24” x ¼" 
  - 2 Acrylic Sheet: 12” x 36” x ¼" 
  - 4 Acrylic Sheet: 24” x 48” x ¼” 
  - 2 Wood Shelf: 12” x 72” 
  - 4 T-Slotted Framing (Wheel) 
    - Stem Mount Caster for 1.5” High Single Rail, 200 lb. Capacity
  - 1 Phenolic Workbench Top 
  - 1 Pair Steel Drawer Slides 
  - 36 Black Corner Brackets 
    - 1-½" Long for 1-½” High Rail T-Slotted Framing
  - 2 T-Slotted Framing (Outside Corner End Bracket) 
    - for 1-½" High Rail
  - 2 T-Slotted Framing (3-Way Outside Corner End Bracket) 
    - For 1-½" High Rail
  - 1 T-Slotted Framing: Double Extrusion/Double Six slot Rail, 4 Ft 
    - Black, 3” High x 1-½" Wide, Hollow
  - 5 T-Slotted Framing: Single Extrusion/Single Four Slot Rail, 10 Ft 
    - Black, 1.5” High x 1.5” Wide, Hollow
  - 1 T-Slotted Framing: Single Extrusion/Single Four Slot Rail, 4 Ft 
    - Black, 1.5” High x 1.5” Wide, Hollow
- Surge Protector Block 
- USB LED Light 
- USED Extension 
- Power Reels 
- 40” TV 
- TV Mount 
- Wireless Keyboard and Mouse

#### 3-D Printed Parts

- Drawer Handle  
- Zima Board Case 
- Power Reel Mounts 
- Printer Waste Chute Bucket

## Processing Materials

- Cut two 66.5” Single Extrusions (SE) out of 2 separate 10’ SE 
- From one leftover 4’5.5” SE (53.5” SE)  
  - Cut out one 21” SE, &amp; one 29.5” SE 
    - Repeat on other leftover 53.5” SE 
      - 3.5” leftover
- From three different 10’ SE, cut three 33” SE’s out on each one. 
  - Three 21” SE leftover
- From 4’ DE, cut two 21” DE’s out.  
  - 6” leftover
- From both 12” x 72” wood shelves 
  - Cut out one 32-1/8” x 12” piece, and one 19-7/8” 12”  piece. (Should have 2 of each)
- From one 24” x 48” acrylic sheet, cut out a 21 ¾” x 33” sheet.
- From another 24” by 48” acrylic sheet, cut out a 20 3/8” x 31 3/8” sheet. 
- From another 24” by 48” acrylic sheet, cut out a 32 &amp; ¾" x 12” sheet. 
- Tap one side of two 21-inch single extrusions (SE) with m8 x 1.25  
- Tap the top side of two 29.5-inch SE’s with m8 x 1.25 and the bottom sides with 3/8-169C2B 
- Tap both sides of two 33-inch SE’s with m8 x 1.25 
- Tap the top side of two 66.5-inch SE’s with m8 x 1.25 and the bottom side with 3/8-169C2B 
- Center the extension cord on the center shelf piece, place the place holders on the extension cord, and use them to mark the shelf piece. 
  - Drill through the marked locations and screw the place holders onto the extension cord and shelf piece using nuts and bolts (file the holes as necessary to screw the parts together)

## Assembly

- Count all pieces and sort
- All L Brackets hae their tops lined up with the given measurements, unless otherwise noted.

### Side Section

- Separate the smallest part of the drawer slide from the slide.  
- On the 21” Double Extrusion 
  - Slide 5 3d printed inserts into the side of the 21” DE. 
    - The inserts should be slid into the part of the DE that you will face inwards on the vignette. 
    - The Inserts should in the top slot on the side of the DE
  - Line the bigger parts of the drawer slide up with the 21” DE 
    - The Flat side of the drawer slide should be touching the DE 
    - The Front of the drawer slide (where the smaller part goes in an out) should be lined up with what will be the side of the DE that faces the front of the vignette
  - Mark the Extrusion 5 times using the holes on the biggest part of the slide. Center the inserts with the marks made 
  - Realign the slide and pre-drill through the holes into the inserts. 
  - Screw into the holes to attach the slide to the DE.
- Begin with a side of the 66.5" SE to make the Vignette side 
  - Screw in L Bracket 5 inches from bottom of extrusion 
  - Slide in additional T nut above 5 inches 
  - Screw in L Bracket 29.5 inches from bottom of extrusion 
  - Attach 21" double extrusion to L Bracket 5 inches from bottom. 
    - Slide 2 T nuts in top side of 21” double
- 29.5-inch single extrusion  
  - Screw in L Bracket 5 inches from bottom 
  - Attach to 21-inch double extrusion with 66.5 single”
- Attach L Brackets where 66.5” single and 21 double meets, and where 29.5” single and 21” double meets 
- Attach L Brackets so that top faces downward (touching with the top of 21” DE”) 
- Repeat all steps to make a second side. 
- Insert 21.5”x 22” side panel in spaces between 66.5” single &amp; 29.5” single 
  - Loosen and adjust L Brackets that are in the way as needed, then readjust to original position.
- Lay both assembled side parts flat and face both parts in opposite directions 
  - Following steps apply to both assembled side parts 
    - Attach 21” SE to L Bracket on 66.5” SE at 29.5 inches
  - Attach 2 L Brackets at each end, outward facing 
  - Attach 2-way corner bracket atop 66.5” in a way that would be facing inward and screw in to connected parts 
  - Attach 3-way corner bracket atop 29.5” in a way that would be facing inward and screw in to connected parts 
  - Screw in L Bracket 4 inches from bottom of 66.5” single 
  - Screw in L Bracket 18 inches from bottom of 66.5” single 
  - Screw in L Bracket 29.5 inches from bottom of 66.5” single 
  - Screw in L Bracket 46.5 inches from bottom of66.5” single 
  - Screw in L Bracket 52.5 inches from bottom of 66.5” single 
  - Screw in L Bracket in line with top of 66.5” single 
  - Screw in L Bracket 4 inches from bottom of 29.5” single 
  - Screw in L Bracket 18 inches from bottom of 29.5” single

### Front and Back

- Set aside tapped 33” singles 
- Attach non-tapped 33” SE to following L Bracket heights on 66.5” SE: 
  - 4 inches 
  - 18 inches 
  - 29.5 inches 
  - 46.5 inches 
    - Slide 2 T nuts inside the front-facing side.
  - 52.5 inches 
    - Slide 2 T nuts inside the front-facing side.
  - Attach 33” SE to following L Bracket heights on 29.5” SE 
    - 4 inches 
    - 18 inches
  - Attach tapped 33” SE to: 
    - 3-way corner bracket on 29.5” SE 
    - 2-way corner bracket on 66.5” SE
- On 66.5” SE, insert back panels in spaces between extrusions at: 
  - 4 inches &amp; 18 inches
- On 29.5” SE, insert front panels in spaces between extrusions at 
  - 18 inches and 29.5 inches
- Insert Wood Shelf between front and back sides at 18” mark 
- Line up other side part and screw together all pieces 
- Stand Frame upward 
- Screw workbench top into L Brackets that are facing outward &amp; connected to 21” SE on side frames 
- Screw wheels in to bottoms of all 29.5” and 66.5” SE’s 
- Assemble TV mount, center T nuts with TV mount, and attach TV and TV mount.

### Drawer

- On the wood shelf pieces, 
  - One inch from the bottom, carve a ¼” thick, 1/8” deep slit from the left end to the right end.
- Insert the 31 &amp; 3/8” x 20 &amp; 3/8” acrylic sheet in the 32 &amp; 1/8” piece so that it is centered.  
- Attach the remaining 32 &amp; 1/8” shelf piece and 19 &amp; 7/8” pieces to the corresponding sides of the acrylic sheet.  
  - The long side of the drawer should be facing up for the next step.
- Drill holes to screw into 
  - Drill 3 holes on each end to secure the touching wood shelf pieces. 
    - Holes should be centered with vertical standing wood shelf pieces.
- Add screws and repeat on the other side. 
- Take 32 &amp; ¾" x 12” acrylic sheet and line it up with the front of the drawer so that the tops are flesh with each other, and so that the sides of the acrylic are even on both ends of the drawer. 
- Place acrylic side of the drawer facing down. 
  - Drill holes to from inside the drawer into the acrylic 
    - Line drill bit up with the drawer and mark where the drill would be to drill halfway into the acrylic. 
    - Drill until the drill enters halfway through the acrylic sheet
- Separate the acrylic sheet and the drawer, and drill into existing holes on the acrylic sheet until the drill enters halfway through the sheet. 
- Line up the same side of the drawer with the acrylic sheet. 
- Add screws.  
  - The acrylic side should be facing down to make it easier to add screws.
- Flip the drawer to face upright. Center the drawer handle, and drill two holes into the handle and top of the drawer. 
- Add screws.  
- On one side of the drawer, take the smallest part of a steel drawer slide and line it up 1 inch from the bottom of the drawer.  
  - The flat side of the drawer slide should be touching the drawer, and the front ends of the drawer and the drawer slide should be facing the same way.
- Drill holes into the center of the 4th, 8th, 10th, and 12th outlined holes from the front of the steel drawer slide. 
- Add screws. 
- Slide on the outer part of the drawer slide. 
- Flip over and repeat the same steps for the drawer slide on the other side of the drawer.

## Troubleshooting

For software glitches, always try refreshing the page using F5 first, and then properly restarting the vignette using the instructions if that does not work.

For specific troubleshooting related to the BambuLabs X1 Carbon 3D Printer refer to this guide [here](https://wiki.bambulab.com/en/x1/troubleshooting)